Re: [PATCH liburing] test: use a map to define test files / devices we need

[Hao Xu <haoxu@linux.alibaba.com>]

在 2020/12/22 上午11:03, Hao Xu 写道:
> 在 2020/12/15 上午10:44, Hao Xu 写道:
>> 在 2020/12/8 下午8:28, Hao Xu 写道:
>> ping...
> Hi Jens,
> I'm currently develop a test which need a device arg, so I
> leverage TEST_FILES, I found it may be better to form
> TEST_FILES as a key-value structure.
> Thanks && Regards,
> Hao
ping again..
>>> Different tests need different files / devices, use a map to indicate
>>> what each test need.
>>>
>>> Signed-off-by: Hao Xu <haoxu@linux.alibaba.com>
>>> ---
>>>
>>> the former implementation use a array for the global list TEST_FILES,
>>> which may causes this:
>>>     TEST_FILES="dev0 dev1"
>>>     dev0 required by test0
>>>     dev1 required by test1
>>> In the <for tst in $TESTS> loop, we run the test for each $dev, which
>>> makes <test0 dev1> and <test1 dev0> run, these are not expected.
>>> Currently I see that statx.c accept argv[1] as a file_name, if someone
>>> writes another test which defines a device(say nvme0n1) in TEST_FILES,
>>> it may cause issues.
>>>
>>>   test/config      |  2 +-
>>>   test/runtests.sh | 13 ++++++-------
>>>   2 files changed, 7 insertions(+), 8 deletions(-)
>>>
>>> diff --git a/test/config b/test/config
>>> index cab270359155..1bd9b40207bb 100644
>>> --- a/test/config
>>> +++ b/test/config
>>> @@ -4,4 +4,4 @@
>>>   # TEST_EXCLUDE=""
>>>   #
>>>   # Define raw test devices (or files) for test cases, if any
>>> -# TEST_FILES="/dev/nvme0n1p2 /data/file"
>>> +# declare -A TEST_FILES=()
>>> diff --git a/test/runtests.sh b/test/runtests.sh
>>> index fa240f205542..1a6905b42768 100755
>>> --- a/test/runtests.sh
>>> +++ b/test/runtests.sh
>>> @@ -5,10 +5,10 @@ RET=0
>>>   TIMEOUT=60
>>>   DMESG_FILTER="cat"
>>>   TEST_DIR=$(dirname $0)
>>> -TEST_FILES=""
>>>   FAILED=""
>>>   SKIPPED=""
>>>   MAYBE_FAILED=""
>>> +declare -A TEST_FILES
>>>   # Only use /dev/kmsg if running as root
>>>   DO_KMSG="1"
>>> @@ -17,7 +17,7 @@ DO_KMSG="1"
>>>   # Include config.local if exists and check TEST_FILES for valid 
>>> devices
>>>   if [ -f "$TEST_DIR/config.local" ]; then
>>>       . $TEST_DIR/config.local
>>> -    for dev in $TEST_FILES; do
>>> +    for dev in ${TEST_FILES[@]}; do
>>>           if [ ! -e "$dev" ]; then
>>>               echo "Test file $dev not valid"
>>>               exit 1
>>> @@ -109,11 +109,10 @@ run_test()
>>>   # Run all specified tests
>>>   for tst in $TESTS; do
>>> -    run_test $tst
>>> -    if [ ! -z "$TEST_FILES" ]; then
>>> -        for dev in $TEST_FILES; do
>>> -            run_test $tst $dev
>>> -        done
>>> +    if [ ! -n "${TEST_FILES[$tst]}" ]; then
>>> +        run_test $tst
>>> +    else
>>> +        run_test $tst ${TEST_FILES[$tst]}
>>>       fi
>>>   done
>>>